A 20 × 10 ft flower bed covered 3 inches deep takes 50 cubic feet of mulch, which is 1.85 cubic yards. Add 5 % for spillage and an uneven surface and you buy about 1.94 yards from a landscape yard, or 27 bags of 2 ft³ from a garden center. The calculator above does the same for any bed, depth, mulch type and bag size, and shows how far one yard and one bag go at your depth.
How the calculator works
Enter the length and width of the bed, or its area if you have already measured it, and the depth you want. If you know the volume, for example the 3 yards a supplier quoted, enter that instead and the calculator turns it into bags. Pick the mulch and the bag size sold near you. The result is the volume to order, the bags, the weight and the truck loads.
Volume
Volume is area × depth. With the area in square feet and the depth in inches, divide the depth by 12 to get cubic feet, then divide by 27 to get cubic yards: 200 × 3/12 = 50 ft³, and 50 ÷ 27 = 1.85 yd³. For a bed of several shapes, measure each part as a rectangle, add the areas and use the area mode. A round bed around a tree is π × radius²: a 6 ft circle is 3.14 × 3 × 3 = 28.3 ft².
Bags
Bagged mulch is sold by volume, not weight. The common sizes are 2 ft³, then 1.5 ft³ and 3 ft³. The number of bags is the cubic feet you need divided by the bag size, rounded up: 52.5 ÷ 2 = 26.25, so 27 bags. One cubic yard holds 13.5 bags of 2 ft³.
Coverage
One cubic yard spread 1 inch deep covers 324 ft², because 27 ft³ × 12 = 324. At any other depth divide 324 by the depth in inches. The calculator shows the same figure with your waste allowance included, which is why it is slightly lower than the table.
| Depth | One cubic yard covers | One 2 ft³ bag covers | One 3 ft³ bag covers |
|---|---|---|---|
| 1 in | 324 ft² | 24 ft² | 36 ft² |
| 2 in | 162 ft² | 12 ft² | 18 ft² |
| 3 in | 108 ft² | 8 ft² | 12 ft² |
| 4 in | 81 ft² | 6 ft² | 9 ft² |
Weight
Mulch is light and its weight depends on moisture more than on the product: a dry yard of shredded bark weighs about 400 to 800 lb and a soaked one up to twice that. The calculator uses typical values (shredded hardwood 800 lb per yard, pine bark nuggets 600, cedar 550, wood chips 700, compost 1,200) only to tell you whether a load fits your pickup. A half-ton pickup carries about one to one and a half yards of dry mulch.
How deep to spread mulch
For most flower and shrub beds 2 to 3 inches is enough to keep moisture in and weeds down. Use 3 to 4 inches on paths and in beds with heavy weed pressure, and less of fine material such as compost, which packs tighter. Keep mulch a few inches away from tree trunks and from the bottom of siding: piled against bark it keeps the wood wet. When you top up an old bed, measure the depth that is still there and enter only the difference.
Bags or bulk
For a small bed bags are easier: they fit in a car and leave no pile on the driveway. Above two or three yards bulk is usually cheaper per yard, but the yard charges for delivery. Enter your local bag and yard prices in the price list to compare: the calculator does not fill in prices, because they vary by region and season.
Common mistakes
- Mixing inches and feet: 3 inches is 0.25 ft, not 3 ft. The calculator converts the units for you.
- Measuring the bed outline but not subtracting a patio or a large shrub in the middle. Use the area mode with the net area.
- Buying for the full depth on top of an existing layer. Rake the old mulch, measure what is left and add only what is missing.
- Forgetting that bag sizes differ between stores. A 1.5 ft³ bag covers a quarter less than a 2 ft³ bag.
Planning the whole yard? Rock beds are figured the same way in the Landscape Rock Calculator, soil for new beds in the Topsoil Calculator, and any other volume in the Cubic Yards to Tons Calculator.