A 20 × 4 ft border covered with 3 inches of river rock takes 20 cubic feet of stone. With 5 % for waste you need 21 cubic feet, 0.78 cubic yards, which weighs about 1.05 tons, or 42 bags of 0.5 ft³. The same bed in lava rock weighs less than half as much: about 0.43 tons. The calculator above works out tons, yards and bags for any bed and rock, and lets you enter your supplier's weight per yard.
How the calculator works
Enter the length and width of the bed, or its area, and the depth. Choose the rock. The result is the weight to order, the cubic yards, the 0.5 ft³ bags, how many square feet one ton covers, and the truck loads. If you already know a volume or a weight, switch the mode and the calculator converts it.
Volume
Volume is area × depth: feet × feet × (depth in inches ÷ 12) gives cubic feet, ÷ 27 gives cubic yards. For a dry creek bed or a curved border, measure the average width at several points. For a circle around a tree, the area is 3.14 × radius², minus the area of the trunk.
Weight
Landscape supply yards sell rock by the ton or by the yard. Weight is volume × density. Rock densities are not standardized and change with the stone and its size, so the calculator uses typical loose values and accepts your supplier's figure.
| Rock | Typical tons per cubic yard | One ton covers at 2 in | One ton covers at 3 in |
|---|---|---|---|
| River rock, ¾–3 in | 1.35 | 120 ft² | 80 ft² |
| Pea gravel | 1.35 | 120 ft² | 80 ft² |
| Marble chips | 1.35 | 120 ft² | 80 ft² |
| Beach pebbles | 1.35 | 120 ft² | 80 ft² |
| Decomposed granite | 1.40 | 116 ft² | 77 ft² |
| #57 crushed stone | 1.40 | 116 ft² | 77 ft² |
| Lava rock | 0.55 | 295 ft² | 196 ft² |
Coverage is 324 ft² per cubic yard at 1 inch, divided by the depth and by the tons per yard. The calculator adds your waste allowance, so its coverage figure is a little smaller than the table.
Compaction
Rounded rock such as river rock and pebbles does not compact, so the default allowance is zero. Decomposed granite is different: it is spread loose and then wetted and rolled into a firm surface, losing about 15 % of its volume, and the calculator adds that automatically when you pick it.
How deep to lay rock
The depth follows the stone size: a layer should be at least about one and a half times the size of a typical stone so that no soil or fabric shows through. Pea gravel and small chips need about 2 inches, ¾ to 1½ inch river rock 2 to 3 inches, and 3 to 5 inch rock 4 to 5 inches. Decomposed granite paths are usually 3 inches compacted over a gravel base. More depth than this only adds weight and cost; it does not stop more weeds.
Bags or bulk
Garden centers sell decorative rock in 0.5 ft³ bags, about 50 lb each. One ton of river rock fills about 40 of them, so above half a ton bulk is almost always cheaper. Bulk rock is delivered by dump truck or picked up by the scoop: a half-ton pickup carries about half a yard of rock at most, because the weight limit is reached long before the bed is full.
Common mistakes
- Ordering lava rock by the ton figures for river rock. Lava rock weighs less than half as much per yard; order it by volume.
- Laying rock straight on soil. Without landscape fabric the stones work down into the dirt within a few seasons.
- Piling rock against siding or over the foundation vents. Keep the finished grade sloping away from the house.
- Choosing rock too large for a thin layer, which leaves gaps the fabric shows through.
For driveway stone and gravel bases use the Gravel Calculator; for wood mulch beds, the Mulch Calculator; to convert any other material, the Cubic Yards to Tons Calculator.