A 1,000 square foot lawn takes about 1,050 square feet of sod once you add 5 % for cuts along the edges. In standard 16 × 24 inch pieces that is 394 pieces; sod farms usually load 450 square feet on a pallet, so you order 3 pallets. The calculator above does this for any area, piece and pallet size, and also figures the grass seed if you would rather seed, the topsoil under the lawn, the starter fertilizer and the edging.
How the calculator works
Enter the lawn area and a waste allowance, and choose sod or seed. For sod, pick the piece size your supplier sells and how much a pallet covers. For seed, pick the grass; the seeding rate fills in and you can change it to the rate on your bag. Then set the topsoil layer, the starter fertilizer and the edge length if you want edging. The result shows what to buy and how much of each.
Sod: pieces and pallets
Sod to order = area × (1 + waste). Divide by the area of one piece and round up for the number of pieces; divide by the area a pallet covers and round up for the pallets. A 16 × 24 inch slab is 2.67 ft², so a 450 ft² pallet holds 168 of them. Farms charge more per piece for a partial pallet, so it often pays to round up to a full one and keep the rest for patching.
| Lawn area | Sod with 5 % | 16 × 24 in pieces | Pallets of 450 ft² |
|---|---|---|---|
| 500 ft² | 525 ft² | 197 | 2 |
| 1,000 ft² | 1,050 ft² | 394 | 3 |
| 2,500 ft² | 2,625 ft² | 985 | 6 |
| 5,000 ft² | 5,250 ft² | 1,969 | 12 |
Seed: pounds by species
Seed = area ÷ 1,000 × the rate in pounds per 1,000 ft², plus the allowance. Rates differ a lot by species because seed sizes do: a pound of Kentucky bluegrass holds about ten times as many seeds as a pound of tall fescue. The defaults are Ohio State University Extension's rates for a new lawn:
| Grass | lb per 1,000 ft², new lawn |
|---|---|
| Kentucky bluegrass | 2–3 |
| Tall fescue | 8–10 |
| Fine fescues | 3–6 |
| Perennial ryegrass | 7–8 |
Mixes follow the rate on the bag. For overseeding a thin lawn, use about half the new-lawn rate. Warm-season grasses such as bermudagrass and zoysia are often planted from sod or plugs rather than seed in the South; enter your bag's rate if you seed them.
Topsoil, fertilizer and edging
Topsoil = area × layer depth. Grass roots mostly in the top 4 to 6 inches, so that is the usual target for a new lawn on poor ground; 4 inches over 1,000 ft² is 12.3 cubic yards. This is the settled volume: loose soil settles, so order 10 to 15 % more, as the Topsoil Calculator does. Starter fertilizer is figured from a nitrogen target: area × pounds of nitrogen per 1,000 ft² ÷ the nitrogen share of the product, the first number on the bag. One pound of nitrogen from an 18-24-12 starter is 5.6 lb of product. Edging is the edge length divided by the length of a piece, rounded up.
Laying sod
Lay sod the day it arrives: it heats up on the pallet within a day in warm weather. Start along a straight edge, stagger the joints like bricks, butt the pieces tight without stretching them, and cut around curves with a sharp knife. Roll the lawn and water it the same day until the soil under the sod is wet. On slopes, stake the pieces until they root.
Common mistakes
- Ordering the exact area. Curves, beds and walkways cost 5 to 10 % in offcuts.
- Assuming every pallet holds 500 ft². Some hold 400 or 450; check before you count pallets.
- Seeding tall fescue at the bluegrass rate. Big seeds need a much higher rate in pounds.
- Laying sod on compacted subsoil. Loosen the ground, add topsoil where it is poor, and grade it to fall away from the house, which you can check with the Slope Calculator.