Cut List Optimizer: boards, pipe and sheets

How it's calculated. For the parts still to cut, the calculator finds the combination that fills one piece of stock best, repeats it while the parts last, and goes on; each cut costs the saw kerf. No plan can use fewer pieces than the total length with kerfs ÷ the stock length.
8 × 70" + 12 × 46" + 8 × 30" from 12' boards, ⅛" kerf → 10 boards, 6.1 % waste (the minimum)
01

What are you cutting?

Stock
Stock length
ftin
in
in
in

Kerf is the width the blade removes: about ⅛ in for a circular or miter saw, 1/16 in for a thin metal blade or band saw. Trim squares up a rough factory end.

02

Parts

ftin
ftin
ftin
Stock to buy
10pieces of 12' 0"
Waste 6.1 %
Parts28
Length of the parts112' 8"
Length of the stock120' 0"
Cuts28
Offcuts from 12"2
The plan uses the fewest pieces possible

Cutting plan

4 × Upright 5' 10" + Upright 5' 10"left 3¾"
4 × Shelf 3' 10" + Shelf 3' 10" + Shelf 3' 10"left 5⅝"
2 × Brace 2' 6" + Brace 2' 6" + Brace 2' 6" + Brace 2' 6"left 23½"

Cutting diagrams

10 × 12' 0" · waste 6.1 %
STOCK 12' 0"× 470"70"left 3¾"× 446"46"46"left 5⅝"× 230"30"30"30"left 23½"
10Stock to buy6.1 %Waste28Cuts28Parts
Price and weight
$
How we calculate

Pieces of stock: for the parts still to cut, the calculator finds the combination that fills one piece best, repeats it while the parts last, and goes on. Each part takes its length plus one kerf; the last part in a piece needs no kerf if it runs to the end. The result is compared with the simple longest-first method, and the plan with fewer pieces wins.

Exact cutting is a hard problem, but a plan like this matches the best possible or is one piece off. The minimum that no plan can beat (total length with kerfs ÷ usable stock length) is shown for comparison.

Sheets: with straight through cuts, parts are laid out in strips across the sheet, as a table saw or track saw cuts them. Without that limit they pack tighter. The sheet count is an upper estimate: a shop's optimizer may save a little more.

To buy
10pieces of 12' 0"

Eight 70 inch uprights, twelve 46 inch shelves and eight 30 inch braces cut from 12 ft boards with a ⅛ inch kerf take 10 boards. That is also the least possible: the parts and their kerfs add up to more than 9 boards. The calculator above finds such plans for boards, pipe, tube or bar from any stock length, and lays out rectangular parts on plywood or metal sheets.

How the calculator works

Choose stock lengths or sheets. For stock, pick the length you buy, the saw kerf, any trim off a rough end and the shortest offcut worth keeping; list the parts with their lengths and quantities. For sheets, enter the sheet size, the kerf, whether every cut must run edge to edge, and whether parts may turn. The result shows how many pieces of stock or sheets to buy, the waste, the cuts and a diagram for each pattern, ready to take to the saw.

Stock lengths

Each part takes its length plus one kerf; the last part in a piece needs no kerf after it if it runs to the end. For the parts still to cut, the calculator finds the combination that fills one piece of stock best, cuts as many pieces that way as the parts allow, and repeats. It also tries the simple longest-first method and keeps whichever plan uses fewer pieces. Exact cutting is a hard problem, but plans like this match the best possible or come within a piece of it.

The check under the result compares the plan with a lower bound: total length of parts and kerfs ÷ usable stock length, rounded up. When the plan equals it, no plan can do better.

Kerf and trim

SawTypical kerf
Circular, miter or table saw, standard blade⅛ in
Thin-kerf blade3/32 in
Metal-cutting cold saw or abrasive blade1/16 – ⅛ in
Band saw1/32 – 1/16 in

Lumber ends are often rough or split, so many carpenters square both ends first: enter that as trim. Metal stock usually comes square. The calculator works in 1/32 inch steps, so fractions add up exactly: three 32 inch parts fit a 96 inch board with no kerf.

Sheets

With straight through cuts on, parts are laid out in strips across the sheet, each strip cut into pieces, as a table saw, track saw or panel saw breaks down a 4 × 8 sheet. Turn it off for CNC, laser or plasma cutting, which can follow any outline and pack parts tighter. Turn off rotation when the grain or a pattern must run one way. The sheet count is an upper estimate: a shop's optimizer may save a little more.

Reading the plan

Each row of the diagram is one cutting pattern: "× 4" means four pieces of stock are cut that way. Cut the longest parts first, mark all parts of a pattern before cutting, and label them as you go. Offcuts at least as long as your "keep from" setting are counted separately so you can use them in the next job.

Common mistakes

Pricing the steel? The Tube Weight Calculator and Steel Weight Calculator give the weight per foot to enter. For framing lumber counts, see the Wall Framing Calculator.

Questions

How do I make a cut list from lumber?

List every part with its length and quantity, choose the board length you buy, and let the calculator group the parts so each board is used fully. It shows each cutting pattern and how many boards to cut that way.

How much should I allow for the saw kerf?

About ⅛ in for a circular saw, miter saw or table saw blade, 1/16 in for a thin-kerf or metal-cutting blade, and 1/32 in for a band saw.

How many 8 ft boards do I need?

Add the part lengths plus one kerf each and divide by 96 in for a lower bound; the real number is that or a little more, depending on how well the lengths combine. The calculator finds the plan.

Can it plan plywood cuts?

Yes. In sheet mode enter the sheet size and the parts; with straight through cuts the layout follows how a table saw or track saw breaks down a 4 × 8 sheet.

Why do two 48 in parts not fit on a 96 in board?

The saw kerf: the first cut removes about ⅛ in, so the second part is ⅛ in short. Buy longer stock or cut one part a little shorter.

What is a usable offcut?

A piece left over that is long enough to keep, 12 in by default. The calculator counts them so you can plan them into the next job.

Related calculators