Beam Deflection Calculator: wood, LVL and steel beams

How it's calculated. A simply supported beam under a uniform load deflects Δ = 5wL⁴ ÷ 384EI at mid-span and carries a moment M = wL² ÷ 8. The deflection is compared with the span divided by a limit: L/360 for floors.
10' span, 300 lb/ft, 2-ply 2×12 DF No. 2: Δ = 5 × 25 × 120⁴ ÷ (384 × 1,600,000 × 356) = 0.12" ≈ L/1,000, well under L/360 = 0.33"
01

Span and supports

ftin

Simply supported: the beam rests on two posts or walls and can rotate there. Fixed: the end is built in and cannot rotate, which cuts deflection two to five times, but only if the connection really holds the end.

02

Loads

lb/ft
ftin
ftin
Weight of the beam

Line load on a beam = load per square foot × the width it carries: a floor with 40 psf live and 10 psf dead load on a beam carrying 6 ft is 50 × 6 = 300 lb/ft. Loads are service (unfactored) loads, as allowable stress design uses them.

03

Beam

Beam
Plies
Deflection
0.122in
2-ply 2x12 Douglas Fir-Larch No. 2 · simply supported · 10' 0"
Deflection ratioL/987
0.333 in allowed at L/36036 %
Maximum moment3,848 ft·lb
Bending81 % used
Maximum shear1,539 lbf
Shear38 % used
Reactions1,539 lbf · 1,539 lbf
Passes bending and deflection

Load, moment, shear and deflection

2-ply 2x12 Douglas Fir-Larch No. 2 · Passes bending and deflection
w = 300 lb/ftL = 10' 0"M3,848 ft·lbV1,539 lbfΔ0.122 inDELIMETRA · FT-IN
0.122 in · L/987Deflection3,848 ft·lbMaximum moment81 %BendingΔ = 5wL⁴ ÷ 384EISimple span, uniform load
How we calculate

The beam is solved by the finite element method with beam elements: any number of uniform and point loads, four support schemes, exact deflections at the nodes. For a simple span under a uniform load it gives the textbook Δ = 5wL⁴ ÷ 384EI and M = wL² ÷ 8.

Lumber: reference design values of the American Wood Council for joists and rafters, which include the size factor and the 15 % repetitive member factor; a lone beam or header of one or two plies loses that 15 % (NDS 4.3.9). Shear: 1.5 V ÷ (b × d) against Fv from the NDS Supplement. Normal load duration, dry service.

LVL: typical 2.0E values (Fb 2,600 psi at 12 in depth, Fv 285 psi, E 2,000,000 psi). Each manufacturer publishes its own; theirs govern.

Steel: allowable moment Fy × Zx ÷ 1.67 (AISC 360-16 F2 and F7) for compact shapes braced along the compression flange; W-shapes ASTM A992 and HSS ASTM A500 Grade C at 50 ksi; HSS properties use the design wall 0.93 t.

Deflection limits follow IBC Table 1604.3; for a cantilever the span in the ratio is twice its length.

This is a check of one member, not a design: connections, bearing, lateral bracing and load combinations are up to the designer, and a building department may ask for a stamped calculation.

Deflection
0.122in

A 10 ft beam made of two 2×12 Douglas Fir No. 2 boards carrying 300 lb per foot sags about 0.12 inch at mid-span, about L/1,000, well inside the L/360 floor limit of 0.33 inch, and uses about 80 % of its bending strength. The calculator above checks any beam like this: any span, four kinds of supports, any number of uniform and point loads, in lumber, LVL, a steel W-beam or steel tube, with the moment, shear and deflection diagrams.

How the calculator works

Set the supports and the span. Add the loads as you know them: a uniform load in pounds per foot over all or part of the span, or point loads at given distances; the beam's own weight can be added. Choose the beam: lumber species, grade, size and plies; LVL depth and plies; a W-shape; a steel tube; or your own E, I and S. Pick the deflection limit. The result is the deflection and its L/ ratio, the maximum moment and shear, the reactions, the share of bending and shear strength used and, when the beam fails, the smallest member of the same kind that works.

Deflection formulas

Beam and loadMaximum deflectionMaximum moment
Simple span, uniform load w5wL⁴ ÷ 384EIwL² ÷ 8
Simple span, point load P at mid-spanPL³ ÷ 48EIPL ÷ 4
Cantilever, uniform loadwL⁴ ÷ 8EIwL² ÷ 2
Fixed both ends, uniform loadwL⁴ ÷ 384EIwL² ÷ 12

For any mix of loads and supports the calculator solves the beam by the finite element method; for the cases in the table it gives exactly these results. E is the stiffness of the material, I the moment of inertia of the section: a beam twice as deep is eight times stiffer.

Deflection limits

IBC Table 1604.3 limits floor members to L/360 under live load and L/240 under total load, roof members to L/240 or L/180 depending on the ceiling below, and L/360 where plaster or stucco would crack. For a cantilever, L in the ratio is twice its length. Under ceramic tile L/480 is a common target, under natural stone L/600 or stiffer.

Strength

Loads

A beam carries the floor or roof halfway to the next support on each side. Multiply the load per square foot by that width: a floor beam carrying 6 ft of floor at 40 psf live and 10 psf dead takes 300 lb per foot. The calculator uses the loads as entered (allowable stress design), so enter the service loads, not factored ones.

What it does not check

Bearing at the supports, connections, lateral bracing of steel, notches and holes, wet or treated lumber and long-term creep are left to the designer. Many building departments want an engineer's calculation for beams in a house; use this to compare options and see which size to ask about. For floor joists and rafters by the span tables, the Joist Span Calculator and Rafter Span Calculator are quicker.

Questions

How do you calculate beam deflection?

For a simple span with a uniform load: Δ = 5wL⁴ ÷ 384EI, with w in lb per inch, L in inches, E in psi and I in in⁴. For a point load at mid-span: Δ = PL³ ÷ 48EI.

What is the deflection limit for a floor beam?

L/360 under live load and L/240 under total load (IBC Table 1604.3): a 12 ft beam may sag 0.40 in under live load. Under tile, L/480 or stiffer is common.

What does L/360 mean?

The span divided by 360. A 15 ft (180 in) beam may deflect 180 ÷ 360 = 0.5 in.

Will a double 2x12 span 12 feet?

Under 300 lb/ft, a 2-ply 2×12 Douglas Fir No. 2 deflects about 0.25 in over 12 ft, well inside L/360, but bending uses about 115 % of its allowable stress, so it fails; a 3-ply works. Check your own load.

Does the calculator check steel beams?

Yes: W-shapes and HSS tube with the AISC allowable moment Fy × Zx ÷ 1.67, assuming the top flange is braced along its length by joists or decking.

Is this enough for a permit?

No. It checks one member for estimating. Connections, bearing, bracing and load combinations need a designer, and many building departments want a stamped calculation for beams.

Related calculators