Roof Truss Calculator: King post, Fink and Howe

How it's calculated. Rise = pitch ÷ 12 × half the span. Top chord = √(half span² + rise²) plus the overhang ÷ cos θ. Number of trusses = roof length ÷ spacing, rounded up, + 1.
24' span, 6/12: rise 6'; top chord √(12² + 6²) = 13.42' + 1.12' overhang = 14.53'; 40' at 24" → 21 trusses
01

Truss

ftin
ftin
Pitch, rise per 12
02

Roof

ftin
Spacing
03

Lumber

Chords
Chord stock length
Webs
Web stock length
Trusses
21trusses
Fink (W) · 24' 0" · 6/12
Rise at the peak6' 0"
Roof angle26.6°
Top chord, each14' 6⅜"
Bottom chord24' 0"
Webs, one truss21.6 ft
Lumber per truss74.7 ft
2×4 × 16 ft boards84
2×4 × 10 ft boards63
Board feet1,316
Connector plates147 pairs
Bottom chord spliced: longer than the stock2 × 12' 0"
Estimate only: trusses are engineered and built by a truss plant (IRC R802.10)

Members of one truss

Top chord14' 6⅜"
Top chord14' 6⅜"
Bottom chord24' 0"
Web 13' 7¼"
Web 27' 2½"
Web 33' 7¼"
Web 47' 2½"

Truss elevation

Fink (W) · 24' 0" · 6/12
ELEVATION, CENTER LINES3' 7¼"7' 2½"14' 6⅜"24' 0"6' 0"1' 1⅜"DELIMETRA · FT-IN
√(run² + rise²) + overhang ÷ cos θTop chord6' 0"Rise at the peak14' 6⅜"Top chord, each147Connector plates
How we calculate

Geometry on member center lines: rise = pitch ÷ 12 × half the span; top chord = √(half span² + rise²), plus the overhang measured along the slope (overhang ÷ cos θ). Web lengths come from the joint positions of each type: the Fink's webs meet the top chord at mid-slope and the bottom chord at the third points of the span.

Number of trusses = roof length ÷ spacing, rounded up, plus one; the two end trusses are usually gable-end trusses with vertical studs instead of webs.

Lumber: each member is cut from the stock length you choose; a bottom chord longer than the stock is split into equal pieces and spliced with plates. Board feet use the nominal size (PS 20).

Real trusses are designed for the building's loads by the truss plant under IRC R802.10 and ANSI/TPI 1: lumber grade, plate sizes and splices come from their drawings. Use this to estimate, compare types or frame a small shed, not to design a house roof.

Trusses
21trusses

A 24 ft wide house with a 6/12 roof has trusses that rise 6 ft at the peak, with top chords about 14 ft 6 in long once a 1 ft overhang is added. On a 40 ft roof at 24 inches on center it takes 21 of them. The calculator above works out the geometry of King post, Fink and Howe trusses, every member length, how many trusses you need, and the boards, board feet and connector plates for an estimate.

How the calculator works

Choose the truss type, the span from outside wall to outside wall, the pitch and the level overhang. Enter the length of the roof and the spacing. Pick the chord and web lumber and the stock lengths you would buy. The result shows the number of trusses, the rise and roof angle, each chord and web length, the lumber per truss and in total, the boards to buy and the plate pairs, with an elevation of the truss to scale.

Geometry

Half the span is the run. The rise is the pitch ÷ 12 × run: a 6/12 roof over a 12 ft run rises 6 ft. The top chord is the hypotenuse, √(run² + rise²), plus the overhang measured along the slope, which is the level overhang ÷ cos θ. Webs connect panel points:

TypeWebsJointsTypical use
King postOne vertical at mid-span4Sheds, garages, porches, short spans
Fink (W)Four, from the bottom chord's third points to mid-slope and to the peak7Most houses
HoweVerticals at the third points of each half, diagonals rising toward the peak12Longer spans and heavier loads

Lengths are on member center lines, which is how truss plants dimension them; the cut length of each web is a little shorter because its ends meet the chords at an angle.

How many trusses

Roof length ÷ spacing, rounded up, plus one: a 40 ft roof at 24 inches is 20 spaces and 21 trusses. The two end trusses are usually gable-end trusses, with vertical studs for the siding instead of webs. Spacing is 24 inches for most houses; 16 inches under heavy roofing such as tile or where the sheathing requires it.

Lumber and plates

The calculator cuts each member from the stock length you choose, chords from one length and webs from another, and counts the boards for all trusses together. A bottom chord longer than the stock is split into equal pieces and spliced with plates; trusses wider than the longest stock, usually 20 ft, have a spliced bottom chord. Board feet use the nominal size: a 2×4 is 0.667 board feet per foot. Each joint takes a pair of connector plates, one on each face.

Engineered trusses

The IRC (R802.10) requires wood trusses to be designed to ANSI/TPI 1, and in practice house trusses come from a truss plant with sealed drawings that set the lumber grade, the plate sizes and the bracing. Use this calculator to compare types and pitches, check a quote, estimate a shed or a garage, or plan the roof framing; for the sheathing and shingles on top, see the Roofing Calculator and the Shingle Calculator, and for site-built rafters instead of trusses the Rafter Length Calculator.

Common mistakes

Questions

How many trusses do I need?

Roof length ÷ spacing in feet, rounded up, plus one. A 40 ft roof at 24 in on center takes 40 ÷ 2 = 20 spaces, so 21 trusses; at 16 in, 31.

How do I calculate the length of a truss top chord?

Half the span and the rise make a right triangle: √(run² + rise²). For a 24 ft span at 6/12, run 12 ft and rise 6 ft give 13.42 ft, plus the overhang measured along the slope.

What is the difference between a King post, Fink and Howe truss?

A King post has one vertical web and suits short spans. A Fink has four webs in a W and is the most common house truss. A Howe has verticals and diagonals and is used for longer spans and heavier loads.

How far apart are roof trusses spaced?

24 in on center is the standard for houses; 16 in is used under heavy roofing or where the sheathing needs it.

How much lumber is in a truss?

A 24 ft Fink at 6/12 with 1 ft overhangs has about 53 ft of chords and 22 ft of webs, about 75 linear feet of 2×4.

Can I build my own roof trusses?

For a shed or a small outbuilding, often. For a house the IRC (R802.10) requires trusses designed to ANSI/TPI 1, which is why they are ordered from a truss plant with engineered drawings.

Related calculators