Asphalt Calculator: tons of hot mix for a driveway

How it's calculated. Tons = square yards × compacted thickness in inches × 110 lb ÷ 2,000, plus about 5 % for waste. 110 lb per square yard per inch is about 147 lb per cubic foot of rolled hot mix.
40' × 12' = 53.3 yd² × 3" × 110 lb = 17,600 lb = 8.8 tons → +5 % = 9.24 tons
01

How much?

Start from
ftin
ftin
in
02

Material

Plant-mixed asphalt as laid and rolled: 110 lb per square yard per inch

1.98 ton/yd³Density

Published value.

03

Allowances and delivery

%
%
yd³
ton
Weight
9.24ton
Hot mix asphalt, compacted · 1.98 ton/yd³ · +0 % / +5 %
Volume4.67 yd³
Area480 ft²
Volume placed4.44 yd³
Truck loads1 · limited by payload
One ton covers52 ft²
Published density

Density and delivery

Hot mix asphalt, compacted · 1.98 ton/yd³ · +0 % / +5 %
DENSITY, TONS PER CUBIC YARDAsphalt millingsHot mix asphalt, compactedCold patch asphalt1.98 ton/yd³LOADS: 1 · limited by payloadDELIMETRA · FT-IN
L × W × depth ÷ 27Formula1.98 ton/yd³Density1Truck loads
Your local prices
$
$
$
$

Prices are not pre-filled: aggregate prices and delivery differ by region and quarry.

How we calculate

Volume = length × width × depth, in consistent units: feet × feet × inches ÷ 12 gives cubic feet, ÷ 27 gives cubic yards.

Weight = volume × loose density. Densities of stone, sand and soil are not standardized: they are measured per ASTM C29 and vary by quarry, gradation and moisture. The calculator starts from typical values and lets you enter your supplier's figure.

Compaction allowance adds the loose material needed to reach a compacted depth; waste covers spillage and an uneven subgrade. Neither is added when you start from a weight you already know.

Soil dug from the ground (bank volume) swells when loosened: 10 yd³ in the ground loads as about 12.5 yd³ at 25 % swell. The weight is the same; the truck volume is not.

Truck loads are limited by whichever runs out first, body volume or legal payload.

To order
9.24ton

A 40 × 12 ft driveway paved 3 inches thick takes about 8.8 tons of hot mix asphalt once it is rolled: 53.3 square yards × 3 inches × 110 lb per square yard per inch = 17,600 lb. With 5 % for waste and uneven base, plan on about 9.2 tons. The calculator above does the same for any area and thickness, and also figures cold patch bags for repairs and asphalt millings for a recycled driveway.

How the calculator works

Enter the length and width, or the area, and the compacted thickness. Choose hot mix, cold patch or millings. The result is the tons to order, the cubic yards, the area and the truck loads; for cold patch, the number of 50 lb bags. If you already know the tons from a quote, use the weight mode to see the area or volume it covers.

Tons of hot mix

Paving plants sell asphalt by the ton. The usual conversion in state DOT paving specifications is 110 lb per square yard per inch of compacted thickness. In other units that is 146.7 lb per cubic foot, or 3,960 lb (1.98 tons) per cubic yard. The formula is:

tons = (length × width ÷ 9) × thickness in inches × 110 ÷ 2,000

For the example: 40 × 12 ÷ 9 = 53.3 square yards; 53.3 × 3 × 110 = 17,600 lb; 17,600 ÷ 2,000 = 8.8 tons. Mixes vary a little with the aggregate, from about 140 to 150 lb per cubic foot; the plant can give you the density of the mix it ships, and the calculator accepts it.

Compacted thicknessTons per 100 ft²One ton covers
1 in0.61164 ft²
2 in1.2282 ft²
3 in1.8355 ft²
4 in2.4441 ft²

Why there is no compaction allowance

Hot mix is spread by the paver about 20 to 25 % thicker than the finished layer and rolled down. The 110 lb figure is already for the rolled layer, so you enter the finished thickness and the tons come out right. The waste allowance covers material left in the truck, hand work at edges and a base that is not perfectly flat. Millings are different: they arrive loose and are compacted on site, so the calculator adds about 20 % for them.

Truck loads

A tandem dump truck hauls about 15 tons of asphalt, a tri-axle about 18 to 20. Asphalt is dense, so the payload, not the box, sets the number of loads. Enter your plant's trucks in the delivery settings.

How thick should a driveway be?

A typical residential driveway is 2 to 3 inches of compacted hot mix on 4 to 8 inches of compacted crushed stone base. Thicker asphalt, or a two-layer pavement with a binder course and a surface course, is used for heavy trucks, soft clay soils and long-lasting work. The base matters as much as the asphalt: most driveway failures start with a thin or wet base. Figure the stone for it in the Gravel Calculator, using crusher run, which compacts hard.

Cold patch and millings

Cold patch is bagged asphalt for potholes and small repairs, sold in 50 lb bags. A bag fills about a third of a cubic foot once tamped: roughly 4 square feet at 1 inch. Fill the hole in layers of about 2 inches, tamping each. Asphalt millings, or recycled asphalt pavement, are ground-up old paving sold by the ton or yard for driveways and paths. They are cheaper than hot mix but rougher, and they compact and bind over time in the sun.

Common mistakes

Planning the edges? Pavers for a border are counted in the Paver Calculator, and a concrete apron in the Concrete Calculator.

Questions

How many tons of asphalt do I need for a 40 × 12 driveway?

At 3 in compacted: 53.3 yd² × 3 × 110 lb = 17,600 lb, or 8.8 tons. With 5 % for waste, order about 9.2 tons.

How much does a cubic yard of asphalt weigh?

About 3,960 lb, close to 2 tons, once it is laid and rolled. That is 110 lb per square yard per inch, or about 147 lb per cubic foot.

How many square feet does a ton of asphalt cover?

About 164 ft² at 1 in, 82 ft² at 2 in and 55 ft² at 3 in of compacted thickness: 2,000 lb ÷ 110 lb per square yard-inch, times 9 ft² per square yard.

How thick should a residential driveway be?

Commonly 2 to 3 in of compacted hot mix over 4 to 8 in of compacted crushed stone base; more over soft soil or for heavy vehicles. Follow your paving contractor or local code.

How many bags of cold patch do I need for a pothole?

A 50 lb bag fills about 0.34 ft³ compacted: about 4 ft² at 1 in, or a 2 × 2 ft pothole 1 in deep. A 2 × 2 ft pothole 2 in deep takes two bags.

Why order asphalt by the compacted thickness?

Hot mix is spread loose and rolled down by about a fifth. The 110 lb per square yard per inch figure is for the finished, rolled layer, so enter the finished thickness and do not add a compaction allowance.

Related calculators